![]() ![]() If you’re having problems getting your kite off the ground or it’s spinning out of control, then try these ways to fix your kite. This will give you the two sides of the cap now, cut a circle from the plastic bag and attach it to the cap. Here is how to do it: First, cut two pieces of a circle from the fleece fabric and stitch up the edges together. Tie ribbons of left-over plastic at regular intervals to it. You need fleece fabric and a plastic bag. Attach a length of twine (about 120cm/4′) to the bottom end of the spine as a tail. This will require some experimenting to find the best spot, but start at a point near the top of the kite.ĩ. By choosing where you attach the string, you control the angle at which the kite flies. The bridle should be long enough so when you pick up the kite by it, it’s at least 20cm (8″) from the kite’s surface.Ĩ. Do the same with the other end of the twine at the other hole. To make the bridle, feed a length of twine through the hole at the top and tie it to the spine. It’s a good idea to reinforce these holes with tape.ħ. Punch two small holes along the spine for the bridle. Use tape to secure to the dowels and the twine, with extra reinforcement at the ends.Ħ. Lay the frame flat, with the crosspiece facing up.ĥ. This will help keep the dowels properly at right angles to each other. Run twine from one end of the crosspiece, to the top end of the spine, to the other end of the spine. It is important that they remain at right angles to each other, and the mid point of the crosspiece is directly on the spine.Ĥ. Fasten the two dowels together using twine and tape. Place the middle point of the crosspiece at right angles on the spine, about 30cm (12″) from one end.ģ. Measure and locate the middle point on the crosspiece, mark with a pencil. Then get your ‘How to make a kite’ building materials together.Ģ. Get creative by decorating your kite design using paints, markers, or stickers.ġ. This Do-it-Yourself project takes 10-steps and one hour to complete. ![]() Strong tape, such as packing tape or electrical tape.Plastic sheeting or recycled garbage bags.Gloves & Bag to place over finished highlights. Apparently this bottle is 20 volume developer and can lift your hair colour 1-2 shades) Mixing Bowl & Spatula. ![]() The longer dowel is the spine of the kite, the shorter dowel the crosspiece. Cream Developer (this contains Hydrogen Peroxide and helps lift your natural colour. We are ready to do one test render and see how the bottle looks. Feel free to experiment with different plastic IOR values to get the desired look. Air has IOR of 1 by definition, which means it is no obstacle for light transmission.Ĭosmetics plastic bottles are commonly made of PET, so we use PET's IOR here, which is 1.575. The Index of Refraction stands for how the material refracts the transmitted light. For the bottle in this scene, we keep it at 1 cm - the thickness of the bottle geometry is around 0.1 cm.Īnother important thing for the accuracy of the material is to set the right IOR. This mode is designed for translucent or refractive materials.įor the proper work of this Color mode we need to set the correct Scatter radius values. ![]() Next, set the Color mode to Scatter coefficient + fog color. Change the mode to Raytraced (refractive) - this introduces refractive properties to the material. The Single Scatter parameter can be changed to get different looks out of the material. We'll rename it to "Bottle_Mtl" for ease of use.įirst, we want the bottle to be translucent, so let's see how to get this effect. Let's start by assigning a V-Ray Fast SSS2 material to the bottle. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |